the

Hey cgm peeps need some help. I've noticed when I start the truck it sounds like it wants to die on me and then runs fine after a few seconds, but this is not a everyday thing, at times turns on fine with no issues, but when it happens sounds like its not shooting enough fuel. Maybe fuel...

Driving to work this morning my mil light came on. I turned around and headed back home and noticed there was no 1st gear. Abs light and trac light on get home and pull the codes In order P0700 P0856 U0121 Another u code I forgot what it was though. Anyone see anything like this ? I recently...

ive got a 2002 silverado 5.3, a few months ago one of my horns went out i noticed it when i was locking my truck the horns blow. well i dismissed it as one horn went bad and never worried about it but a few weeks later i went to blow the horn and nothing it clicks from the relay. i take the...

Been looking everywhere online for a 3" drop block and can't manage to find them only see them for s10 truck. Anywhere I can get one??

hello all i was wondering if i could get some help. i have had my drl's working properly before but now they are being stupid. i shot a little video. this video show the signals working both as 4-ways and as left and right signal. the passenger side is working as it should. the...

So I can't sell my truck for 8k so I was wondering if anyone would be willing to trade cash+stock parts so I can sell my truck for cheaper? Coilovers with lower arms Have 17+ spindles I can sell outright Rear shocks(ridetech single adjustable) Wheels -ss20's with 275/40r20 tires, will come...

2007 Lifted Chevy Silverado Show Truck - only 39,700 miles Located in North NJ This is a very clean truck, inside, out and underneath. Truck has been pampered, it has never seen Off-Road, never Trailered, or Abused and rarely driven in the past 6 years. A/C heat and dual climate control work...

I bought a 1988 chevy 1500 with a 355 crate motor. Where do I hook up the draft tubes so they don't leak oil all over engine Sent from my SM-S820L using Tapatalk

Looking for recommendations on what I should get to fix my horrible paint an to keep it nice. I do not have a machine but I would like to get one. Looking for the best bang for my buck. I basically have the basic cheap soap from the auto parts store and rags. Sent from my SM-G935V using Tapatalk

This one was a big bitch. Mainly new car prep with a coating because he just got this less than a month ago. Process: Foam cannon pre soak IronX bath Foam & wash Clay CarPro essence polish CarPro Eraser wipe down Gyeon Mohs ceramic coating (2 coats) on all paint & wheels CarPro PERL on...

ive got a 02 silverado ext cab with rough country leveling kit the driver side upper control arm is pretty much sitting on the droop stop. my passenger side is close but isnt as bad, my driver side torsion bar bolt is turned in more than my passenger side but my passenger side sits higher than...

Has anyone ever shipped out their nbs cluster to be rebuilt? The battery gauge crapped out on me a while back, but now my speedo is acting up. I could replace the steppers myself, but I'm not that comfortable with electronic repair. I tried to replace an iphone screen a couple years ago, fried...

I have a set of the dual front shocks off a NBS. Shocks only. Have about 10k on them. They're still good. Selling for a friend. Asking $250/OBO for all four. Sent from my iPhone using Tapatalk

To get some good advice and several car parts sites suggestions (lol!) I've decided to create a new thread and discuss the best possible way to lift my truck without spending a fortune. From the beginning I simply wanted to add a set of floor mats for better interior protection, that's where the...

I have a 2000 Silverado ecsb z71. So far i have swapped in a built 4l60(4l65), denali cluster(with red leds), double din swap(with denali bezel), 05 tahoe 17 inch 5 spokes, 10k his & lows, switchbacks, new headlights & taillights, painted my bowtie, stripped molding off(need to get adhesive off...

This will be slow and painful, I traded a friend my bagger for a chassis for my Syclone, well he didn't have time to build it so I received this Blazer instead! I have had it for a while, and have not been interested in working on it until now. Lays frame on 20'some Chromoly tube chassis and...

Sizzold

Thinking of doing something similar, maybe a little cleaner job of cleaning up where the bar was removed.. My truck for reference Sent from my ex's closet

I've got a 06 ext cab silver I want to go with a 3/5 on 275/45R22s but if I can get away with a 4/6 on same wheels and tires without rubbing or having problems going over speed bumps I would go with that. Any idea or pictures would help a...