spindle

My spindle rubs my bag when lifted and put a hole in the bag, was initially just the drivers side. Apparently I need more lift because the inner tires are wore the fuck out, and I'd rather fix this problem so I can drive higher before I put new tires on Sent from a secure terminal using the...

Looking to get some stock 17's for spares. Who has trimmed the BJ bolt orc what needs to be done, cutoff wheel? Is it safe? Looking at these while I save up for Billets n use my current 22s on my tahoe Sent from my SPH-L710 using Tapatalk

Does anybody have pics of their ext cab with the true short bed? I thought that's what I had until I saw the 5.8 today. I'm eager to compare now Sent from my SCH-I605 using Tapatalk

2012 Silverado LT extended cab 5.3 RC 2.5" level Firestone Ride Rite with compressor Daystar airbag cradles HIDs in lows and fogs Lo pro roll up bedcover 40 series Flows dumped Stock wheels and tires 25% tint Color match mirror caps and door handles; color matched front end coming...

Had a buddy change my shoes and drums Monday night. Mine were wore down to the metal. He did everything in about 2 hours. Well last night I was pulling into my gfs house (in her car, mine was parked) and noticed the inside of my driver side rear tire wet. Got under it and both back tires are...

I'm looking for some old belltech 2504 or chassis tech drop spindles. Sent from my iPhone using Tapatalk

New here but wanted to share my journey with my truck. I've got an 03 extended cab silverado and recently slammed it. Went with McG flip, notch and shackles (havnt got around to putting the shackles on due to my bolts being seized) but will get to it! Up front I have 2" djm arms with McG 16+...

2" CTS Brand Drop Spindles for 99-06 GM 1500 Got them as a payment and don't want them. Yes they have light surface rust but I'll clean them and spray some rustoleom primer on them and they can be seperated from the control arms. PM or text me 817-583-0188 located in Haltom City, TX $180

I have a RCSB cateye 2wd, with 2" drop shackles on it. It still sits a little higher in the back, some don't notice, but I do and it bothers me a lot. I am thinking about getting 3" coil spacers. Is this a good idea? Or would I be better off dropping the back some. And how would I go about doing...

Hey guys, I'm fairly new to the forum here, but a long time GM fan. Started off with a '04 sierra, but moved up to my '11 crew cab over the holidays. Now on to the Build. This will be a very slow process for the time being, as I have no truck fund and don't have much extra to put towards mods...

I have 2 rough country spindles that give my front end a 3" lift (so I was told) along with add a leafs an if needed hub extenders. I already have 18" aftermarket wheels on the truck I'm new to suspension lifts so my question: Is there anything else I need besides an alignment to complete...

Hello everyone im Jamie and i have a GMC some might have seen on other GM forum site.

Did a little more to the truck. Before i was cranked with cognito uppers, stock rear... Now i de cranked a little bit, and added a 4" spindle and 3" tapered block. Rides alot better now. I also put a 2" spacer on the carrier bearing because it had a vibration taking off and it made a growling...

selling absolutely everything from a 2000 ecsb Z71. no 4wd axle shafts. everything is up for sale except the center console and dash pieces as well as the engine. parts of interest 2" lift blocks $30 shipped Steel cowl hood $150 picked up Hd Grille and Bumper $350 picked up everything else is...

Ok I have a 2000 silverado scsb, it already has a belltech 3/4 drop, a 2 inch drop spindle up front and a one inch drop spring up front, and out back it has both front and rear shackles and a c notch, I'm wanting to go down to a 5/7, I was thinking a belltech 3 inch drop spring up front and a...

I have a 4" rear drop from hangers and shackles and want to go to a flip for 6" or 7" drop. Can I keep the hangers and just go with a 1" raise shackle (which I have from diff project). This would mean that I start with a 1" drop before flipping axle. I have helper bags already. Just...

I have been searching and lurking and checking out some damn nice trucks on this site but still have some questions. My '02 NBS ECSB 2WD is currently lowered 3/4 with coils and hangers/shackles. I am running Tahoe 20's. I want to go lower but wondering what clearance will be like...

I had the pleasure of getting the first few sets of Belltech's new 2" Drop Spindle for the 07-14 GM Truck. This spindle is to be used with 3" or more of drop. The spindle puts the balljoint at a better angle, improved bumpsteer and you are able to get the alignment closer to specs. My...

Belltech released their part numbers for the 2014 Silverado/Sierra 2WD this week. The NNNBS (2014) will use the same coil spring, spindle, front sway bar and rear shocks as the NNBS (07-13). Belltech did design a new flip kit. The new flip kit for this model truck corrects the axle position and...

Im curious if anyone has the CST spindles only or really any 3" spindle lift on their nnbs. I have a 2011 sierra and I'm looking to do a spindle lift only up front and a 2" block out back. Any body running this setup? I have searched for a few days and have come up empty handed.