Straights ftw, figured y'all will have a jest at the end Lolz
http://www.youtube.com/watch?v=NMquwcfkRls
Sent from my fuckin iPad
http://www.youtube.com/watch?v=NMquwcfkRls
Sent from my fuckin iPad
I ran one with high flow cats for a few years and for a little with long tubes.
High flows
http://youtu.be/1eliWuzErkk
And headers
http://youtu.be/5cc93WTEY7k
http://youtu.be/m98Y542YTck
My setup right now is high flow cats and a single 12 inch bullet to a dumped 8 inch tip. Piping is three inches. I want louder and cutting out the cats seems like the cheapest way to get that, but I don't want it sounding like complete shit haha
Sent from my SCH-R760 using Tapatalk 2
You will be somewhere between those two sounds. I wouldn't say either setup sounded bad, but my truck was pretty loud with the headers into bullet dumped. It just got annoying but I always thought it sounded good.
You will have to tune out your o2 sensors if you cut the cats off so that's an added expense.
I will still have stock manifolds for a while though, so how will that affect the sound compared to headers?
It's just going to sound a bit less throaty honestly, nothing to be concerned with. Cutting cats off will make it more raspy than what it is now and it will be louder.
damn, I guess I never posted my setup. currently have Magnaflow 18" muffler s in/d out. About to throw my Pacesetter's on with their ory pipe and new cats, all 3" piping, 22" Magnaflow dumped behind the axle.
[video=youtube_share;J1_lUQub9nk]http://youtu.be/J1_lUQub9nk[/video]
[video=youtube_share;n2Do9oGzs_c]http://youtu.be/n2Do9oGzs_c[/video]
[video=youtube_share;J1_lUQub9nk]http://youtu.be/J1_lUQub9nk[/video]
[video=youtube_share;n2Do9oGzs_c]http://youtu.be/n2Do9oGzs_c[/video]
Last edited:
same ford resonator ad before, but now dumped under the bed with a 4.5" tip and my cats are gone
Last edited by a moderator:
idle and slowly bringing it up to 2000 RPM, all stock other than Cherry Bomb Extreme and the factory tailpipe hacked off
I just installed a xr1 too it is quieter at idle but it has a nice deep tone really happy with it. Also no more rasp that I had with lts n flowmaster 10 series.
Cam 5.3l first start up, open headers.
Cam 6.0l first start up, open headers.
In cab- 6.0l, CalSpeed longtube headers, ory, single 3" 18" Dynomax Bullet in front of an Aeroturbine 3030xl, 4" dmax tailpipe to a 6" tip...exhaust leaks like a mofo.
Same exhaust as above, but 5.3l
Cammed 5.3l, Pacesetter longtubes, ory, Aeroturbine 3030xl, 4" tailpipe. No Bullet in front of Aero. Excuse the dirty ass truck.
Still don't have a good walk around vid of current setup. Getting tired of aeroturbine's drone....
Cam 6.0l first start up, open headers.
In cab- 6.0l, CalSpeed longtube headers, ory, single 3" 18" Dynomax Bullet in front of an Aeroturbine 3030xl, 4" dmax tailpipe to a 6" tip...exhaust leaks like a mofo.
Same exhaust as above, but 5.3l
Cammed 5.3l, Pacesetter longtubes, ory, Aeroturbine 3030xl, 4" tailpipe. No Bullet in front of Aero. Excuse the dirty ass truck.
Still don't have a good walk around vid of current setup. Getting tired of aeroturbine's drone....
Cam 5.3l first start up, open headers.
Cam 6.0l first start up, open headers.
In cab- 6.0l, CalSpeed longtube headers, ory, single 3" 18" Dynomax Bullet in front of an Aeroturbine 3030xl, 4" dmax tailpipe to a 6" tip...exhaust leaks like a mofo.
Same exhaust as above, but 5.3l
Cammed 5.3l, Pacesetter longtubes, ory, Aeroturbine 3030xl, 4" tailpipe. No Bullet in front of Aero. Excuse the dirty ass truck.
Still don't have a good walk around vid of current setup. Getting tired of aeroturbine's drone....
I have the 3030 non resonated and no drone here but I also dont have headers like yourself
No idea but it's pretty bad. I guess it's just the right wavelength to cause drone or some shit. I want to look into an aerochamber or 22" maggy