I've run into another fucking wheel dilemma and I need some input. All of my Gear 737v's are peeling VERY badly including the one I just had replaced. I've finally accepted the fact you just cant run any type of mirrored finish wheel year around in the northeast. I'm going to warranty the Gears...
For Sale: Used Magnacharger TVS1900 for Cathedral port head engines.
Easily fits: 2007-2013 4.8L, 5.3L Truck/SUV; 2006-2009 Trailblazer SS
Can be made to fit: 2002-2007 4.8L, 5.3L, 6.0L with 4 bolt throttle body swap
Supercharger integrity has been reviewed by an authorized Eaton Repair...
Raceline
Bonspeed
Intro
Boze
Billet Specialties
boyd
Colorado Customs
Who else is in the game. Im looking for some 22"s, and trying to weight out my options.
Suggestions are welcome fellas!
I'm pretty sure we've never really discussed this in depth. But I'm putting on my Zone 1.5" body lift on my NBS this weekend and was just looking for some tips and tricks from those that have done it.
My main concern is how you handle the front clip/core support. My thinking is, remove all...
newbie from houston, Tx.
currently just purchased a 2014 silverado texas edition 5.3 LT.
thinking of raising it 2" with 33s just to look nice.
im colormatching the front and rear bumpers with handle sometime before winter is done.
my question is i want to upgrade the bulbs for reverse...
For the 03-06 Silverados with center consoles, the upper trim pocket/panel piece, will an Escalade piece go in and flow with the rest of the console?
Link to said Escalade piece...
So I just finished doing a suppose to be 5/8 drop on my truck, the rear is perfect where it should be but the front still end up staying the same height when it was 7" drop, guy I bought springs from said they were 2" springs which I went a head and cut a 1/4 coil to make them 3", not sure if he...
It is going to be gorgeous outside the next few days and I have a free weekend so I'm going to get a few things done to the Sierra that have been building up. One of my issues is that, starting around the time I put on the 243 heads, the passenger side header rubs on the frame rail right as it...
For a very long time now everybody keeps asking me why I don't make a build thread. So today - I'm bored - and here it is. For those who don't know I have an 02 HD front end obsession. My two trucks are always works in progress but one I'm getting quite happy with the result. So without further...
most of you guys know my truck by now, but wanted to start a build thread here since i don't like gmfs at all anymore. lol
just a few details
2007 classic
at 143k
5.3 auto 4x4
basic ecsb truck
nothing fancy
leveled with horrible angles, 3" block
cai, cheap single chamber muffler...
I've been thinking a while about switching to an A/T tire and switching out my 4" blocks for the 4.5" blocks I have. The truck right now has 1.5" of lean but the rear just seems to sit too low and I think bringing it up .5" would be perfect. I've also been thinking of switching out my nitto...
So I'm really undecided on what to do with my truck now that I have the HD hood and grille. I've been running over these three options in my head and can't make up my mind, so I'd like some input from the CGM family on what direction to go.
1) 3" level with 2" rear block. For the front I would...
03 silverado. Currently have 2 JL 12s. With a JL amp.
Been thinking of building a box for 4 subs total.
I can't decide with 4 12s or 2 12s and 2 10s.
The 12s would be ran together and 10s together on 2 amps.
If 4 12s then I'd run two amps to two subs.
But trying to figure out what we be...
Hey everyone!
Some of you may have heard rumors of a staff project in the works and we're finally at a point where we're confident we can let you in on the secret .
For about a month and a half we've been working on bringing you guys a CustomGM.com 2015 Calendar, featuring the 12 ROTM winners...
Looking for ideas of how you complete the escalade door handle swap for the tail gate?
I have esky handles at the shop right now being painted and I am not sure what to do with the tail gate. Currently I have the textured junk and I know I could spend hours sanding and smoothing then...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.