Recent content by justinghump

  1. justinghump

    Khaos' RCSB Thread

    When I swapped the 6.0 and did the other work (including the drop shackles) to my Reg Cab I ended up with a vibration between 40-45 mph. Have you figured anything out? Ive tried 2* shims so far with no real change. You will like the 05 brakes...they're a nice swap.
  2. justinghump

    The Old Man's 2500HD

    After a few trips around FL, we got the U-haul and headed for MT. Finished product for now. Hoping to get the Dune 8's Mounted this summer as well as put on the Esky Handles.
  3. justinghump

    The Old Man's 2500HD

    Did not end up taking a lot of pictures of the wiring for the overhead console. I ordered one of the black Aluminum blanks, and we put in 5 switches and a digital volt meter. Light bar and horns mounted. Helping as usual. Hood back on and final check.
  4. justinghump

    The Old Man's 2500HD

    Replaced the clunking ISS Mocking Cables for Dual batteries New Rear Pods Wiring for seats, lights and heated mirrors. Intake Manifold on and EGR Deleted. Horns mounted and light bar mount in progress.
  5. justinghump

    The Old Man's 2500HD

    New UCAs, Bump Stops, 5100s, Tie Rod Ends, Ball Joints, Sway Bar endlinks/bushings, wheel bearings, and brake lines.
  6. justinghump

    The Old Man's 2500HD

    Painted the frame with POR 15 and topcoat after cleaning. That was my first time using it. Very tough stuff if you get it on you... New Seals on rear axle New 5100s Putting the receiver and wiring harness on New 4L80 in Before new front end parts... Hanging the bed (before painted...
  7. justinghump

    The Old Man's 2500HD

    Here are some pictures of the teardown/rebuild that we did in July. Before: Disassembly and pressure washing. Pulling the old 4L80e Starting the front suspension Cognito sent me two Drivers side UCAs. That was neat. New 4L80e
  8. justinghump

    The Old Man's 2500HD

    Small update, moving snow at work has kept me busy to say the least. This past week the coolant steam tube between the heads began leaking, replaced it with a Holley part because GM discontinued the factory part. Ended up doing plugs, wires and an oil change while I was in there and had the...
  9. justinghump

    The Old Man's 2500HD

    A lot has changed since I first created this thread as I haven't had time to update it. I left the Sunshine State for Montana and traded off the regular cab to my dad before I left. I thoroughly went through this truck before moving. Mostly maintenance and reliability mods but some appearance...
  10. justinghump

    Sticker/Decal Thread 2.0

    Could use a couple more. For New ToolBox etc...
  11. justinghump

    Another new project thread...this time AM General HMMWV

    I think they are 8x6.5 but with some serious offset differences...
  12. justinghump

    Justinghump's '02 RCLB Build Thread

    Looks good man, I definitely like them tucked up like that. What wires did you use?
  13. justinghump

    Hulknastys 12 Denali Duramax Build

    Looks great so far, I was sad to see the old truck go but I understand. My girlfriend's dad has a black/black '13 and it is an awesome truck...
  14. justinghump

    Justinghump's '02 RCLB Build Thread

    Thanks bud, we ran 1/2" line from the tank (5 gal long off of a semi) and we used a PacBrake 3.5 cfm compressor. Seems to flow pretty well. My dad made a badass basket to hang the compressor, I got a mudflap and made two shields, one for each side, as the tank is on the passenger and the...
  15. justinghump

    Justinghump's '02 RCLB Build Thread

    Yep, stock converter. definitely feel like it could use a stall but I would like a 4l80e...